UTSI Activated Carbon Fibers (ACFs)
Surface activated carbon fiber products are produced from fibers produced in the UTSI carbon fiber labs.
Various surface treatments results in designed properties towards improved adsorption and desorption of the various chemicals.
Typical applications are water and air-filtration and electrodes for various applications.
Isotropic Pitch-Based ACFs
- Relatively low cost associated with much higher yield
- High surface area and controllable pore size and distribution
- Tailored pore surface chemistry and functional groups
- Higher adsorption capacity and selectivity
- Higher adsorption kinetics due to greatly improved contact efficiency
- Design flexibility
- Ease of regeneration
Introductions to the Research of ACFs
Over the past decade it has become abundantly clear that water contamination and green house gases are of increasing concern in the United States and throughout the world[1-3]. They have prompted industry to develop advanced new materials and improve the performance of existing processes to address these problems. In many cases, adsorbents have been determined to provide the best available technologies for the removal of trace contaminants from water and air. However, the current state-of-art has many limitations including inadequate adsorption/ion exchange capacity, kinetics, selectivity, and scalability. The current generations of ion exchange/carbon adsorbents are primarily in the form of beads or granules, which limit contact efficiency (both the available surface area and the path length to active sites). Increasing surface area by decreasing particle size is counterproductive as the ensuing increase in pressure drop makes scalability impractical for removing trace contaminants from water and air. Thus, design of new, well-characterized, advanced adsorbents represents a unique approach to solving these problems.
Research on the UTSI activated carbon fibers is expected to impact adsorbent technology, which could have profound effects within the field of water and air purification, catalyst support, separation of chemical and biochemical, medicine, fuel cell and hydrogen storage.
Traditionally, adsorbents have been the primary materials used for removal of impurities for both water and air, since they usually have high surface areas. It is well known that small pores, such as micropores (< 2 nm) and mesopores (2 – 50 nm), result in the large surface areas responsible for adsorption; Pore size, pore size distributions, and surface area, as well as pore surface chemistry are the major factors in the adsorption process.
2.1 Natural problems of conventional carbon adsorbents
Granular activated carbon (GAC), one of widely used conventional adsorbents, has been commercially available since the early 1900’s and is used extensively for air and water clean-up primarily due to their low cost. The raw material for activated carbon can be any organic material with a high char yield (i.e. coal, peat, coconut shells, or certain polymers). Activation occurs when the carbon layers are etched away through an oxidation reaction resulting in the formation of a porous carbon network with high surface area. GACs have been accepted as the industry standard for adsorbing unwanted chemical compounds from water and air. As a result, they have become ubiquitous throughout industry, wastewater treatment facilities and even in households for point-of-use drinking water purification. However, GACs display disadvantages such as slow kinetics, bad selectivity and less than 100% working capacity, since a significant portion of their porosity is relatively inaccessible (the working capacity is affected by the very small micropores in the interior of the GAC that do not easily desorb). They also have other drawbacks including costly reactivation and limited design flexibility.
2.2 Advantage fibrous adsorbents
Fibrous activated carbons (ACFs) offer a number of advantages over GACs, including greatly improved contact efficiency with the media leading to greater rates of adsorption, much higher surface areas (up to 2500 m2/g) and the potential for greatly simplified in situ regeneration through electrical resistance heating. Unfortunately the commercially available ACFs are very expensive (~$100/lb), in part because they suffer from huge weight losses during activation, and are very brittle and susceptible to wear and tear during their handling.
- 1. Vörösmarty C, Green J. P, Salisbury J. and Lammers R. B. “Global water resources: vulnerability from climate change and population growth”. Science 2000, 289, 284-288.
- 2. Aldhous P. “The world’s forgotten crisis – Over a billion people cannot get clean water, and things are getting worse”. Nature. 2003, 422, 251.
- 3. Kerr R. A. “How hot will the greenhouse world be?”. Science. 2005, 309(5731), 100.
- 4. Najm I. N, Snoeyink V. L, Lykins B. W. and Adams J. Q. “Using powdered activated carbon: a critical review”. JAWWA. 1991, 83, 65-76.